Android SoundPool的简单使用
一、SoundPool相对于MediaPlayer的优点
- SoundPool适合 短且对反应速度比较高 的情况(游戏音效或按键声等),文件大小一般控制在几十K到几百K,最好不超过1M,
- SoundPool 可以与MediaPlayer同时播放,SoundPool也可以同时播放多个声音;
- SoundPool 最终编解码实现与MediaPlayer相同;
- MediaPlayer只能同时播放一个声音,加载文件有一定的时间,适合文件比较大,响应时间要是那种不是非常高的场景
二、SoundPool
SoundPool soundPool;
//实例化SoundPool
//sdk版本21是SoundPool 的一个分水岭
if (Build.VERSION.SDK_INT >= 21) {
SoundPool.Builder builder = new SoundPool.Builder();
//传入最多播放音频数量,
builder.setMaxStreams(1);
//AudioAttributes是一个封装音频各种属性的方法
AudioAttributes.Builder attrBuilder = new AudioAttributes.Builder();
//设置音频流的合适的属性
attrBuilder.setLegacyStreamType(AudioManager.STREAM_MUSIC);
//加载一个AudioAttributes
builder.setAudioAttributes(attrBuilder.build());
soundPool = builder.build();
} else {
/**
* 第一个参数:int maxStreams:SoundPool对象的最大并发流数
* 第二个参数:int streamType:AudioManager中描述的音频流类型
*第三个参数:int srcQuality:采样率转换器的质量。 目前没有效果。 使用0作为默认值。
*/
soundPool = new SoundPool(1, AudioManager.STREAM_MUSIC, 0);
}
//可以通过四种途径来记载一个音频资源:
//1.通过一个AssetFileDescriptor对象
//int load(AssetFileDescriptor afd, int priority)
//2.通过一个资源ID
//int load(Context context, int resId, int priority)
//3.通过指定的路径加载
//int load(String path, int priority)
//4.通过FileDescriptor加载
//int load(FileDescriptor fd, long offset, long length, int priority)
//声音ID 加载音频资源,这里用的是第二种,第三个参数为priority,声音的优先级*API中指出,priority参数目前没有效果,建议设置为1。
final int voiceId = soundPool.load(context, R.raw.sound, 1);
//异步需要等待加载完成,音频才能播放成功
soundPool.setOnLoadCompleteListener(new SoundPool.OnLoadCompleteListener() {
@Override
public void onLoadComplete(SoundPool soundPool, int sampleId, int status) {
if (status == 0) {
//第一个参数soundID
//第二个参数leftVolume为左侧音量值(范围= 0.0到1.0)
//第三个参数rightVolume为右的音量值(范围= 0.0到1.0)
//第四个参数priority 为流的优先级,值越大优先级高,影响当同时播放数量超出了最大支持数时SoundPool对该流的处理
//第五个参数loop 为音频重复播放次数,0为值播放一次,-1为无限循环,其他值为播放loop+1次
//第六个参数 rate为播放的速率,范围0.5-2.0(0.5为一半速率,1.0为正常速率,2.0为两倍速率)
soundPool.play(voiceId, 1, 1, 1, 0, 1);
}
}
});
本文由 创作,采用 知识共享署名4.0 国际许可协议进行许可。本站文章除注明转载/出处外,均为本站原创或翻译,转载前请务必署名。最后编辑时间为: 2021/01/07 02:19